If you need to replace the connection pins from the base, follow this guide:
Remove the 2 screws form the base.
Identify the pin connector and its metallic sheet. Remove the 2 screws from the metallic sheet.
Connection pins are glued with hot glue. Proceed to carefully heat with hot air and remove the connection pins and its connector from the LED’s elctronic board. Please beware of the pins polarity.
Insert the new pins following instructions in reverse order.
Reassemble the base.
https://coolifting.com/wp-content/uploads/2021/06/DSC_8540.png333500cl-administradorhttps://coolifting.com/wp-content/uploads/2021/06/logo-web-max.pngcl-administrador2021-06-18 13:19:192021-06-23 18:11:41Coolifting Base - Connection pins replacement
Take the gun out from the base while pressing the right hand button. The Language selector and Settings screen should show up on the display.
Confirm the selection by pressing the trigger.
Screen now shows the Language Selection. Change the language selected with the right button and accept by pressing the trigger.
The software will reload automatically in the language selected.
Step 1
Step 1-2
Step 3
https://coolifting.com/wp-content/uploads/2021/06/DSC_8523-copia-e1624002499716.png500333cl-administradorhttps://coolifting.com/wp-content/uploads/2021/06/logo-web-max.pngcl-administrador2021-06-18 09:51:152021-07-01 16:22:52Coolifting language change
Components needed: -> 5 x plastic caps replacement -> 1 x plastic blue tip replacement -> 1 x ceramic tip (including temperature probe)
Part 1- Gun opening
Identify the 5 caps covering the screws and remove them
Remove the blue tip with a screwdriver
Remove the sticker covering the buttons with help of a sharp tool
Remove the 5 screws
Carefully separate the two housing parts while pressing the button indicated on the image
Gun is now opened
Step 2-1
Step 2-2
Step 3-1
Step 3-2
Step 4
Step 5-1
Step 5-2
Step 6
Part 2 – Remove Screen and logic board
In the following steps, you will disconnect the cables and connectors attaching the logic board. The cables are for the following components:
Temperature probe
Product presence sensor
Trigger connector
LED’s connector
Injector connector
Power supply connector Please beware of the conector polarity!
Base connector pins
Resistance tip connector
Remove the logic board and screen to facilitate manipulation in the next steps.
Part 3 – Remove injector
Remove the 2 screws in order to remove the injector
Gently remove the 2 silicone tubes from the vial dispenser
Extract the ceramic tip from the injector
Gently clean the injector tip to remove any trace of dirt
Add silicone to the injector tip as showed in the image.
Insert the new ceramic tip. Be Careful: do not extract the ceramic tip if the silicone has not solidified. This could clog the outflow hole, thus becoming the injector unusable.
Once the silicone has dried out, replace the injector, reconnect the silicon tubes, replace the 2 injector screws and reconnect the logic board.
Part 4 – Calibration
As the resistance from the ceramic tip is now new, you will need to perform a calibration:
Equipment needed: · Multimeter · Room Thermometer
Place the gun in its base until it is fully charged.
Take the gun out from the base while pressing the right hand button (see picture on the left). The Language selector and Settings screen should show up on the display.
Change the selection to “Settings” by pressing the right hand button.
Confirm the selection by pressing the trigger.
Screen now shows the default battery voltage preconfigured.
Use the multimeter to measure the current battery voltage. Use the two buttons to adjust the voltage on the screen until it matches with the value measured on the voltimeter. Confirm by pressing the trigger.
Next screen shows the default preconfigured room temperature. Use the two buttons to adjust the temperature until it matches with the value measured on the room thermometer. Confirm by pressing the trigger.
Press the trigger on the screens that follow until you reach the home screen. At this time all the changes will be saved.
Reassemble the gun by following Gun Opening instructions in reverse order.
Step 5
Step 6-1
Step 6-2
Step 7
https://coolifting.com/wp-content/uploads/2021/06/IMG_4934.jpg667500cl-adminhttps://coolifting.com/wp-content/uploads/2021/06/logo-web-max.pngcl-admin2021-06-11 09:58:222022-01-04 12:22:39Ceramic Tip replacement
Components needed: -> 5 x plastic caps replacement -> 1 x plastic blue tip replacement -> 1 x electronic board
Part 1 – Gun Opening
Identify the 5 caps covering the screws and remove them
Remove the blue tip with a screwdriver
Remove the sticker covering the buttons with help of a sharp tool
Remove the 5 screws
Carefully separate the two housing parts while pressing the button indicated on the image
Gun is now opened
Step 2-1
Step 2-2
Step 3-1
Step 3-2
Step 4
Step 5-1
Step 5-2
Step 6
Part 2 – Screen and electronic board replacement
In the following steps, you will disconnect the cables and connectors attaching the logic board. The cables are for the following components:
Temperature probe
Product presence sensor
Trigger connector
LED’s connector
Injector connector
Power supply connector Please beware of the conector polarity!
Base connector pins
Resistance tip connector
Remove the logic board and screen to facilitate manipulation in the next steps.
Part 3 – Calibration
Equipment needed: · Multimeter · Room Thermometer
Place the gun in its base until it is fully charged.
Take the gun out from the base while pressing the right hand button (see picture on the left). The Language selector and Settings screen should show up on the display.
Change the selection to “Settings” by pressing the right hand button.
Confirm the selection by pressing the trigger.
Screen now shows the default battery voltage preconfigured.
Use the multimeter to measure the current battery voltage. Use the two buttons to adjust the voltage on the screen until it matches with the value measured on the voltimeter. Confirm by pressing the trigger.
Next screen shows the default preconfigured room temperature. Use the two buttons to adjust the temperature until it matches with the value measured on the room thermometer. Confirm by pressing the trigger.
Press the trigger on the screens that follow until you reach the home screen. At this time all the changes will be saved.
Reassemble the gun by following Gun Opening instructions in reverse order.
Step 5
Step 6-1
Step 6-2
Step 7
https://coolifting.com/wp-content/uploads/2021/06/DSC_8517.png333500cl-adminhttps://coolifting.com/wp-content/uploads/2021/06/logo-web-max.pngcl-admin2021-06-11 09:58:202022-01-04 12:20:06Screen and logic board replacement
Components needed: -> 5 x plastic caps replacement -> 1 x plastic blue tip replacement -> 1 x battery
Part1 – Gun opening
Identify the 5 caps covering the screws and remove them
Remove the blue tip with a screwdriver
Remove the sticker covering the buttons with help of a sharp tool
Remove the 5 screws
Carefully separate the two housing parts while pressing the button indicated on the image
Gun is now opened
Step 2-1
Step 2-2
Step 3-1
Step 3-2
Step 4
Step 5-1
Step 5-2
Step 6
Part 2 – Battery replacement
Remove the 2 screws in order to remove the injector and have easy acces to the power supply wire.
Disconect the power supply wire. Please beware of the conector polarity
The battery might be attached with hot glue; in order to detach the battery, proceed to heat the glue with hot air.
Remove the battery and replace it with a new one.
Insert the injector back with its screws.
Reconect the power supply wire. Please beware of the conector polarity
Step 2
Part 3 – Calibration
Equipment needed: · Multimeter · Room Thermometer
Place the gun in its base until it is fully charged.
Take the gun out from the base while pressing the right hand button (see picture on the left). The Language selector and Settings screen should show up on the display.
Change the selection to “Settings” by pressing the right hand button.
Confirm the selection by pressing the trigger.
Screen now shows the default battery voltage preconfigured.
Use the multimeter to measure the current battery voltage. Use the two buttons to adjust the voltage on the screen until it matches with the value measured on the voltimeter. Confirm by pressing the trigger.
Next screen shows the default preconfigured room temperature. Use the two buttons to adjust the temperature until it matches with the value measured on the room thermometer. Confirm by pressing the trigger.
Press the trigger on the screens that follow until you reach the home screen. At this time all the changes will be saved.
Reassemble the gun by following Gun Opening instructions in reverse order.
A cookie or computer cookie is a small information file that is saved every time you visit our website. Some cookies are ours and others belong to external companies that provide services for our website.
Cookies can be of various types: technical cookies are necessary for our website to function. Other cookies serve to improve our page, personalize it or show you advertising tailored to your searches and interests. You can accept all these cookies by pressing the ACCEPT button or configure or reject their use by clicking on the COOKIE SETTINGS section.
For more information, see the Cookies Policy on our website.
Welcome to the basic information on cookies on the website, the entity's responsibility: BEAUTYGUN SL
A cookie or computer cookie is a small information file that is saved on your computer, "smartphone" or tablet every time you visit our website. Some cookies are ours and others belong to external companies that provide services for our website.
Cookies can be of various types: technical cookies are necessary for our website to function, they do not require your authorization and are the only ones that we have activated by default.
The rest of cookies serve to improve our page, to personalize it based on your preferences, or to be able to show you advertising tailored to your searches, tastes and personal interests. You can accept all these cookies by pressing the ACCEPT button or configure or reject their use by clicking on the COOKIE SETTINGS section.
For more information, see the COOKIES POLICY on our website.
Necessary technical cookies
So that our website can work. Enabled by default.
Technical cookies are strictly necessary for our website to function and you can navigate through it. These types of cookies are those that, for example, allow us to identify you, give you access to certain restricted parts of the page if necessary, or remember different options or services already selected by you, such as your privacy preferences. Therefore, they are activated by default, and your authorization is not necessary.
Through the configuration of your browser, you can block or alert of the presence of this type of cookies, although said blocking will affect the correct operation of the different functionalities of our website.
Types of cookies
ANALYSIS COOKIES For the continuous improvement of our website. You can enable or disable them.
Analysis cookies allow us to study the navigation of users of our website in general (for example, which sections of the page are the most visited, which services are used the most and if they work correctly, etc.).
From the statistical information on navigation on our website, we can improve both the operation of the page and the different services it offers. Therefore, these cookies are not for advertising purposes, but only serve to make our website work better, adapting to our users in general. By activating them you will contribute to such continuous improvement. You can enable or disable these cookies by checking the corresponding box, being disabled by default.
FUNCTIONALITY AND PERSONALIZATION COOKIES To improve the functionality and personalization of our website based on your preferences. You can enable or disable them.
Functionality cookies allow us to remember your preferences, to personalize certain characteristics and general options of our website, each time you access it (for example, the language in which the information is presented to you, the sections marked as favorites, your browser type, etc.).
Therefore, these types of cookies do not have an advertising purpose, but by activating them you will improve the functionality of the web page (for example, adapting to your browser type) and its personalization based on your preferences (for example, presenting the information in the language that you have chosen on previous occasions), which will contribute to the ease, usability and comfort of our page during your navigation. You can enable or disable these cookies by checking the corresponding box, being disabled by default.
ADVERTISING COOKIES To improve the management of the advertising displayed on our website, so that it is more useful and diverse, and less repetitive. You can enable or disable them.
Advertising cookies allow us to manage the advertising spaces included on our website based on criteria such as the content displayed or the frequency with which the ads are displayed.
For example, if you have been shown the same ad several times on our website, and you have not shown a personal interest by clicking on it, it will not appear again. In summary, by activating this type of cookies, the advertising displayed on our website will be more useful and diverse, and less repetitive. You can enable or disable these cookies by checking the corresponding box, being disabled by default.
BEHAVIORAL ADVERTISING COOKIES To show you advertising tailored to your searches, tastes and personal interests. You can enable or disable them.
Behavioral advertising cookies allow us to obtain information based on the observation of your browsing habits and behaviors on the web, in order to be able to show you advertising content that best suits your personal interests and tastes.
To make it very easy for you, we will give you a fictitious example: if your last searches on the web were related to suspense literature, we would show you advertising about suspense books.
Therefore, by activating this type of cookies, the advertising that we show you on our website will not be generic, but will be oriented to your searches, tastes and interests, thus adjusting exclusively to you. You can enable or disable these cookies by checking the corresponding box, being disabled by default.
Cookie settings
We use different services that use functionality and personalization cookies, analysis, advertising and behavioral advertising: